The list below is a compiled list of the communication and error codes coming from Screen CTP devices. This list should help you determine what is happening on your device.


E 01=[E 01: Undefined command.]

E 02=[E 02: Command sequence error.]

E 03=[E 03: Undefined parameter.]

E 04=[E 04: Parameter value out of range.]

E 10=[E 10: Recorder is offline.]

E 11=[E 11: An error preventing command execution.]

E 12=[E 12: Exposure is aborted by the engine.]

E 13=[E 13: Exposure is aborted by the user.]

E 14=[E 14: Busy executing the last command, exposure is disabled.]

E 15=[E 15: Recorder is in the semi-stand-by state, exposure cannot be started.]

E 20=[E 20: Image data is lost due to handshake failure.]

E 21=[E 21: Image data would not be started.]

E 26=[E 26: Connection is unexpectedly disconnected.]

E 40=[E 40: Invalid response value from $PASS.]

E 41=[E 41: Not logged in.]

E 42=[E 42: Already logged in by other host.]

E 43=[E 43: Already logged in by the same host.]

E 44=[E 44: Under maintenance/setup via Web page.]

E 45=[E 45: Received ST W from the engine prematurely.]

E 46=[E 46: Error detected on EP-B101 unit main board.]

E 47=[E 47: Communication port was not closed by the host after data transfer is completed.]

E 48=[E 48: Detected CRC error.]

E 49=[E 49: Command response time out.]

R 00=[R 00: Refer to the recorder for the message.]

R 01=[R 01: Unload the media.]

R 02=[R 02: Collect the media.]

R 03=[R 03: Set up the media.]

R 04=[R 04: Unload the media and set up a new media.]

R 05=[R 05: Collect the media and set up a new media.]

R 06=[R 06: Set up a larger size media.]

R 07=[R 07: Unload the media and set up a larger size media.]

R 08=[R 08: Collect the media and set up a longer size media.]

R 09=[R 09: Set up a media of a desired type and size.]

R 10=[R 10: Unload the film and set up a media of a desired type and size.]

R 11=[R 11: Collect the media and set up a media of a desired type and size.]

R 12=[R 12: Low on remaining media.]

@SR D S=[:Recorder is busy or off line.]

[ErrorMessages]

ERROR 14h=[Cover Open]

ERROR 31h=[Media Empty]

ERROR 50h=[Media Jam]

ERROR 60h=[Data Failed]

ERROR 61h=[No Response]

ERROR 62h=[I/F Card Failed]

ERROR 800h=[Check Recorder]

ERROR 801h=[Recorder Stopped]

ERROR 802h=[Job Canceled]

ERROR 803h=[Wrong Recorder]

ERROR 804h=[Check Processor]

ERROR 805h=[Invalid Parameter]

ERROR 806h=[Data Time-Out]

ERROR 807h=[Output Disabled]

ERROR 808h=[Incorrect Magazine]

ERROR 809h=[Media Size Error]

ERROR 80Ah=[Device is busy]

ERROR 80Bh=[Recorder not found]

ERROR 80Ch=[Sequence Error]

ERROR FFE=[Unknown Error]

[WarningMessages]

ERROR 900h=[  Cut line distance (paper feed vale) out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 901h=[  Page margin out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 902h=[  Leading edge out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 903h=[  Trailing edge value out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 904h=[  Image margin out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 905h=[  Punch margin out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 906h=[  Image margin for tail punch out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 907h=[  Punch margin for tail punch out of range: %d - %d mm (%.3f - %.3f inches)]

ERROR 908h=[  Media is already being discharged.]

ERROR FFFFFFFFh=[ Running low on memory]

[TemplateMessages]

DOWNLOAD MAGAZINE INFO=[Downloading magazine(%d) setup...]

END SEPARATION=[Completed: %s]

INVALID PCI VERS=[>>> Switching to FPIF (FPGA-1: %s)]

INVALID CTRL VERS=[>>> Switching to FPIF (Control ROM: %s)]

UNIT_BUSY=[Recorder is used by the host (%s)]

UNIT_RESERVED=[Recorder is reserved by the host (%s)]

[IndexStrings]

STRING 1=[Starting Separation(%d): %s]

STRING 2=[Effective Output Time: %ld second(s).]

STRING 3=[Job aborted.]

STRING 4=[Job completed.]

STRING 5=[Recorder is not responding.]

STRING 6=[ second(s).]

STRING 7=[ERROR: Connected to a different recorder.]

STRING 8=[Unknown error.]

STRING 9=[Film is unloaded.]

STRING 10=[Plate is unloaded.]

STRING 11=[Intermediate is unloaded.]

STRING 12=[Recorder is released.]

STRING 13=[Failed to unload.]

STRING 14=[Failed to release recorder.]

STRING 15=[Default]

STRING 16=[Reserve Recorder]

STRING 17=[Loading / Spinning Drum]

STRING 18=[Start Exposure]

STRING 19=[Data transfer failed.]

STRING 20=[  Value is adjusted to %d mm (%.3f inches.)]

STRING 21=[WARNING:]

STRING 22=[  Failed to download virtual magazine info]

STRING 23=[Magazine name does not match!"]

STRING 24=[Please wait...]

STRING 25=[Error]

STRING 26=[Color number is used by others.]

STRING 27=[Color name is already defined.] 

STRING 28=[Color number out of range (%d - %d)!]

[RecorderStatus]

INITIALIZE=[Initializing...]

IDENTIFY=[Checking Recorder ID...]

BUSY=[Recorder is busy...]

OFFLINE=[Recorder is off line...]

RESERVE=[Reserving recorder...]

PREPARE=[Setting up recorder...]

STANDBY=[Standby (Spining Drum)...]

RECORDING=[Recording...]

RECORDING FINISHED=[Recording Completed...]

INQUIRING=[Downloading...]

DISCHARGE=[Discharging...]

ABORTING=[Aborting...]

CLOSING=[Done...]

[DeviceMenus]

MENU 1=[Unload Film]

MENU 2=[Unload Plate]

MENU 3=[Unload Intermediate]

MENU 4=[Release Recorder]

MENU 5=[Cyan]

MENU 6=[Magenta]

MENU 7=[Yellow]

MENU 8=[Black]

MENU 9=[Update Magazine Info]

MENU 10=[Clear Device Log]

MENU 11=[Update Magazine Info]

MENU 12=[Edit Color Table...]

MENU 13=[Setup Device Connection...]

[DischargeOptions]

DO NOT UNLOAD=[Don't Unload]

AFTER EXPOSURE=[After Page]

AFTER JOB=[After Job]

PRE-UNLOAD=[Pre-Unload]

[CutLineOption]

CUTLINE OFF=[Off]

CUTLINE ON=[On]

CUTLINE CUSTOM=[Custom]

[PageOptions]

ALIGN LEFT=[Left]

ALIGN CENTER=[Center]

ALIGN RIGHT=[Right]

[PunchOptions]

PUNCH ON=[On]

PUNCH OFF=[Off]

PUNCH CUSTOM=[Custom]

[BurnOutOptions]

BURN-OUT ON=[On]

BURN-OUT OFF=[Off]

BURN-OUT CUSTOM=[Custom]

[UnitOptions]

inches=[inches]

mm=[mm]

[Cassettes]

CASSETTE 0=[Default]

CASSETTE 1=[Cassette 1]

CASSETTE 2=[Cassette 2]

CASSETTE 3=[Cassette 3]

CASSETTE 4=[Cassette 4]

CASSETTE 5=[Cassette 5]

CASSETTE 6=[Cassette 6]

CASSETTE 7=[Cassette 7]

CASSETTE 8=[Cassette 8]

CASSETTE 9=[Cassette 9]

CASSETTE 10=[Cassette 10]

DEFAULT CASSETTE=[Default]

CASSETTE TEMPLATE=[Cassette %d]

[PreLoadOptions]

EACH JOB=[Each job]

ALWAYS ON=[Always on]

[WindowsNT]

007=[German]

009=[American]

00C=[French]

011=[American]

American=[enu]

Japanese=[jpn]